How to fix bootloop or unbrick Cherry  Mobile Flare S3 Octa Kitkat


Hi guys, I’m going to teach you on how to fix bootloop or deadboot in Flare S3 Octa in Kitkat version via SPFT. After releasing an update in Flare S3 Octa for lollipop version a lot of member in the group encountered bootloop problem. Afterwards I decided to make a new tutorial on how to fix it. This is  easiest way to understand with image attachment. Just follow the procedure carefully. If your using Windows XP/7 follow the method I to install driver. Then for Win 8 /10 for the method II. Once successfully installed the driver proceed in flashing firmware or stockrom via SPFT.
Cherry Mobile Flare S3 Octa Fix Bootloop/Unbrick/Deadboot



FLARE S3 OCTA(kitkat) stockrom

(adsbygoogle = window.adsbygoogle || []).push({});



1. Download Mediatek Driver and Extract then Install the driver for 32 or 64 bit operating system of windows 7.

Driver Choose 32 or 64 bit

2.  Before you plug your phone in PC, you need to focus in Device Manager, then plug your phone without the battery you only have approximately 5 seconds to appear MT65xx device that shows under Other devices, you need to right click it as soon as you see it.

Then after you rightclick, click to Update driver software
3. Then choose – Browse my computer for driver software
Browse Driver
Browse the Mediatek MT65xx Preloader Driver folder
Make sure you know the version of OS to choose the right driver for your PC.
Choose your OS version, then choose if 32-bit or 64-bit for your PC.
E.G. s Win7  folder:
usb2ser_Win7.inf – if 32-bit
usb2ser_Win764.inf – if 64-bit
4. Another options, to find right driver for your phone is to open your internet while your phone is connected without the battery and automatically searching driver for your phone.
1. Download all necessary files and Enable USB Debugging mode in your phone..
2. Install Drivers USB_VCOM_Driver.rar
In Device Manager Right click on PC name(Right Side) and then click on Add legacy hardware as shown in image below.
add legacy
Now in Add Hardware Wizard click on Next » Install the Hardware that i manually select from a list (Advanced) » Show All Devices » Next » Have a Disk, Now select the any inf file from where you extracted the downloaded VCOM driver package.
mediatek preloader
3.  Now Click on Next and select Install this driver software anyway and wait for finishing the process.
Install driver anyway
4.  After installation is finished then Restart your computer, That’s it.
If still not success in installing driver just Disabled Driver Signature Verification
1. Go to PC Settings>General>Troubleshoot>Advanced Options>Startup Settings>Disabled Driver Signature Enforcement>Then Restart
disabled driver signature verification
Once you disabled. Then follow the procedure above to install the driver. Once success proceed to next step.
1. Open flash_tool.exe, click on the Download Tab
Extract the downloaded AFP2 stock rom to the new folder you created.

Click flash tool


2. Click Scatter-loading and browse for the scatter file (MT6592_Android_scatter)
3. For Bootloop only
Make sure flashing mode is set to “Download Only” and check mark all except Preloader.
Note: If deadboot/hardbrick set “Download+Format” and check Preloader.
4. Click Download.



5. Turn off your phone, connect your phone to the PC and wait for the flashing to commence.
6. Green Circle image with check will show once flashing is completed. That’s it!

7. Disconnect your phone in USB cord then open if still bootloop then try to factory reset in recovery settings. To go in recovery mode reboot your phone hold and press power on and volume up simultaneously until recovery mode appeared.

(adsbygoogle = window.adsbygoogle || []).push({});

Cherry Mobile Flare S3 Octa™


  1. boss bakit hindi kulay yellow lumalabas saken pag nagdadownloading na ? kulay pula sya bakit ganon? tas antagal nya madownload reply asap boss thanks

  2. Reflash lang uli. Check din usb chord at kung nkainstalled na ang driver.

  3. sir bkit ganun inupdate ko na peru nung nereboot ko wla na makita sa homescreen kulay puti lang lahat at mga guhit na iba2 kulay.. panu ulit ibalik sir? help naman po tnx.

  4. sir ganon din po sakin, after ma flash nging black screen na lang siya tsaka my mga guhit na din, paano po ito???

  5. Sir Bakit po hindi na ma on your CP ko….no reaction na para bang wlang battery your CP ko?…..please sir need answer

    • Nope. Pwede mo pa buhayin yang cp mo even on deadboot just flash the stockrom via SPFT and follow this tutorial

    • ayaw na mag ON kahit ilaw or charge pero kung mtrace pa ng PC via USB cord kaya pang buhayin yan via SPFT

      • Paano po kung hindi ma detect ng PC? kasi meron sa steps na dpat enable usb debugging e hindi ko naman ma enable kasi spft lng recovery ko at di makapasok hangang logo lng

  6. sir bakit po hndi na nkakapunta sa bios.. lagi nlang po nasa logo

  7. Paano i eenable USB Debugging? di ako umaabot ng homescreen, blackscreen lang sya. buset na update to. buting hindi ko na inupdate to lollipop. sinundan ko ng maayos lahat ng steps dito pero hangang enable usb debugging lng ako. pero na ok naman ang usb chord ko kasi pag plug ko sa pc ko nagchcharge naman. pero no signs sa pc na may naka connect na phone. pa help naman mga sir yung nakagawa nito.

  8. sir yung CM s3 power ko on and off lng sya sa logo. pano ba to maayos?

  9. Bat ganun, ok naman lahat. na flash sya ng maayos, pero pag open ko umiilaw lang sya kahit pmunta ako sa recovery ganun lng. iilaw then patay agad. uhm. paano to sir?


Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.